Ublox GPS NEO6MV2 Flight Control Modul APM2.5 2.0 seriell UART 3,3-5V Arduino ESP32 ESP8266 Raspberry

Ublox NEO6MV2 Flight Control Module Set incl. Pinheader © androegg

Ublox NEO6MV2 APM2.0 APM2.5 Flight Control Module © androegg

Ublox NEO6MV2 3.3-5V serial Flight Control Module © androegg

Ublox NEO6MV2 external GPS Antenna © androegg

Ublox NEO6MV2 external GPS Antenna with U.FL Connector © androegg

Das NEO6MV2 GPS Flight Control Modul ist ein kompaktes und leistungsstarkes GPS-Empfänger Modul. Kernstück des GPS Moduls bildet der Neo-6 aus dem Hause u-Blox.

Das GPS NEO6MV2 GPS Flight Control Modul bringt bereits alles
mit was zum Betrieb benötigt wird:

• externe GPS Antenne mit passendem U.FL Anschluß, Kabellänge 70mm ±5%
• integrierter EEPROM
• Pinleiste

Das GPS NEO6MV2 GPS Flight Control Modul erlaubt eine Spannungsversorgung von 3,3V bis 5V und eigent sich für eine Vielzahl typischer MCU’s wie beispielsweise:

• Arduino
• STM
• ESP8266
• ESP32
• STM
• Raspberry Pi
• usw.

NEO6MV2 GPS Modul

Die Signalausgabe des NEO6MV2 GPS Modul erfolgt seriell über die UART Schinttstelle (3,3V Level).

Zum Betrieb an MCU’s mit einem 5V Level wird entweder ein Levelshifter, oder Spannungsteiler beispielsweise R1 1KΩ, R2 2KΩ benötigt.

The NEO6MV2 GPS Flight Control Module is a compact and powerful GPS receiver module. The heart of the GPS module is the Neo-6 from u-Blox.

The GPS NEO6MV2 GPS Flight Control Module comes with everything that is required for operation:

• external GPS Antenna with U.FL Connector, cable length 70mm ±5%
• integrated EEPROM
• Pinheader

The GPS NEO6MV2 GPS Flight Control Module allows a power supply of 3.3V to 5V and is suitable for a variety of typical MCU’s such as:

• Arduino
• STM
• ESP8266
• ESP32
• STM
• Raspberry Pi
• usw.

NEO6MV2 GPS Module

The signal output of the NEO6MV2 GPS module is serial via the UART interface (3.3V level).

For operation on MCUs with a 5V level, either a level shifter or a voltage divider, for example R1 1KΩ, R2 2KΩ, is required.

Ublox NEO6MV2 GPS Flight Control Module features:

• Based on u-blox NEO-6M GPS module with on-board backup battery and built-in EEPROM
• Comes with external U.FL ceramic antenna for better signal strength
• It is compatible with various flight controller boards designed to work with a GPS module, APM2.0 and APM2.5 just to name a few
• module comes with built-in voltage regulator
• Operating voltage: 3.3V to 5VDC
• Communication interface: UART TTL, 9600bps
• LED signal indicator.
• Pin-out
  • VCC: 3.3 to 5VDC
  • RX: Data receive in (input to GPS module)
  • TX: Data transmit out (Out from GPS module)
  • GND: Ground (Logic and power ground)
• Receiver Type: 50 channels, GPS L1(1575.42Mhz)
• Horizontal Position Accuracy: 2.5m
• Navigation Update Rate: 1HZ (5Hz maximum)
• Capture Time:
  • Cool start: 27s
  • Hot start: 1s
• Navigation Sensitivity: -161dBm
• Communication Protocol: NMEA, UBX Binary, RTCM
• Serial Baud Rate: 4800-230400 (default 9600)
• Operating Temperature: -40°C ~ 85°C
• Operating Current: 45mA
• TXD/RXD Impedance: 510Ω
• Dimension:
  • Module Board 36 x 26 mm
  • external GPS Antenna 25 x 25 x 6.7 mm (w/o cable)
• Weight: 22g