Tasmota ESP-01+ ESP8266 Modul 32Mbit 10 Pin Version

5,48 

Das DS18B20 ESP-01 Set beinhaltet 1 Stück DS18B20 Temperatur Sensor Modul und 3 Stück Dupont Kabel female/female 100 mm

Lieferzeit: sofort

94 vorrätig

EAN Code 4260633291664 Artikelnummer: 304585458704 Kategorie: Schlagwörter: , , , , , ,

Beschreibung

Tasmota ESP-01+ ESP8266 Modul 32Mbit OTA Flash 10 Pin Version 5GPIO’s IO0 IO4 IO5 IO12 IO16

ESP-01+ with 5 GPIO’s and 4MB SPI Flash  © androegg

ESP-01+ with Tasmota Firmware © androegg

Das EI-OT ESP8266 ESP-01+ Modul basiert auf dem ESP8266EX, identisch mit dem Standard ESP-01 / ESP-01S Modul, verfügt aber über einen größeren Flash Speicher sowie 10 Pins und zusätzliche GPIO’s.

Das EI-OT ESP-01+ Modul verfügt die Tasmota Firmware für 4MB ESP8266 Module und erlaubt ein OTA (Over the Air) Update auf die gewünschte Tasmota Firmware

ESP8266 ESP-01+ Modul

Das EI-OT ESP-01+ Modul wurde für den erweiterten Einsatz eines ESP-01 optimiert.

  • schneller 32Mbit Flash Speicher unterstützt bis zu 2x120MHz. im Dual und bis zu 4x104MHz. im Quad Modus
  • GPIO0 ist wie beim Standard ESP-01 Modul verfügbar um den Flash Modus zu aktivieren
  • GPIO16 unter anderem benötigt für Deep Sleep Wake Up ersetzt den GPIO2 des Standard ESP-01
  • CH_EN wurde nicht ausgeführt und durch den GPIO12 ersetzt
  • GPIO4 und GPIO5 (oftmals für I2C verwendet) wurden auf 2 zusätzliche Pins, Pin 9 und Pin 10 ausgeführt

 

ESP8266 ESP-01+ Modul mit 32Mbit Flash Speicher und 5 GPIO’s

 

Kompatibilität

Das EI-OT ESP-01+ Modul ist von der Hardware kompatibel mit ESP-01 Erweiterungen wie

  • CH340 ESP-01 Programmer
  • Temperatur Sensor Module wie
    DS18B20
    DHT11
    DHT22
  • WS2812 RGB Controller Board
  • ….

Insofern GPIO2 bei dem jeweiligen Modul benötigt werden sollte, muss die Signalausgabe durch GPIO16 innerhalb der Firmware ersetzt werden. Des Weiteren werden Pin9 und Pin10 (GPIO4 und GPIO5) nicht mit dem 8-poligen Sockel verbunden / bleiben frei.

 

Our EI-OT ESP8266 ESP-01+ Module is based on ESP8266EX and is fully compatible to Standard ESP-01 / ESP-01S Standard Modules. Compared to ESP-01 Standard Module the EI-OT ESP-01+ got a 32Mbit Flash and 10 Pins.

The EI-OT ESP-01+ Module is comes with standard Tasmota Firmware for 4MB ESP8266 Modules, allows also OTA (Over the Air) Update for specific compiled Tasmota Firmware

ESP8266 ESP-01+ Module

The EI-OT ESP-01+ Module is optimized for a wide range of applications

  • fast 32Mbit Flash supports up to 120MHz. in Dual Mode and 4x104MHz. in Quad Mode
  • same GPIO0 function / position as ESP-01 Standard Module to select boot or flash mode
  • GPIO2 Pin is replaced thru GPIO16 (used for deep sleep wake up)
  • CH_EN Pin is replaced thru GPIO12
  • GPIO4 and GPIO5 (often used for I2C) connected to 2 additional Pins (Pin9 and Pin10)

 

ESP8266 ESP-01+ Module with 32Mbit Flash and 5 GPIO

 

compatibility

The EI-OT ESP-01+ Module is fully compatible with standard ESP-01 extension boards for example

  • CH340 ESP-01 Programmer
  • Temperatur Sensor Module
    DS18B20
    DHT11
    DHT22
  • WS2812 RGB Controller Board
  • ….

In case of GPIO2 is required, just forward GPIO2 functions to GPIO16. Also Pin9 and Pin10 (GPIO4 and GPIO5) are not connected to 8 pole socket.

EI-OT ESP-01+ ESP8266 WiFi Module Features

 

 

Pinleiste 2-reihig 5-polig 2,54mm Raster GND

GPIO1 TXD

GPIO16

GPIO12

GPIO0

RST

GPIO3 RXD

3V3

GPIO5

GPIO4

Pin Header 2-rows 5 pins 2.54mm Pitch GND

GPIO1 TXD

GPIO16

GPIO12

GPIO0

RST

GPIO3 RXD

3V3

GPIO5

GPIO4

Zusätzliche Informationen

Das könnte dir auch gefallen …

Anmelden