Farb Color Sensor Modul TCS3200

5,69 

Farb Color Sensor Modul TCS3200 TCS230 2,7-5V 400-950nm Arduino ESP8266 ESP32

Lieferzeit: sofort

Nicht vorrätig

Beschreibung

Farb Color Sensor Modul TCS3200 TCS230 2,7-5V 400-950nm Arduino ESP8266 ESP32

TCS3200 Color Sensor Module © androegg

TCS3200 Color Sensor module

Arduino Color Sensor Module © androegg

Arduino Color Sensor Modul

TCS3200 Color Sensor Module Pin Out © androegg

Arduino Farbsensor Modul

Das TCS3200 Farb Sensor Modul erlaubt Eingangsspannungen zwischen 2,7V bis 5V. Diesbezüglich ist das TCS3200 Sensor Modul für typische MCU’s wie beispielsweise

  • ESP8266
  • ESP32
  • ESP8285
  • Arduino
  • Raspberry Pi
  • STM
  • usw.

geeignet.

Das TCS3200 Farb Sensor Modul verfügt über eine lichtempfindliches Diodenarray TCS230 von Taos. zur Detektion von sichtbarem Licht.

Das Diodenarray des TCS230 basiert auf einen 8×8 Array

  • 16 blau
  • 16 rot
  • 16 grün
  • 16 clear

und erfasst darüber hinaus ein Spektrum von ca. 400 bis 950 nm.

Die 4 weissen LED’s dienen zur Ausleuchtung der Messfläche.

 

Die Signalverarbeitung des TCS3200 Color Sensor Modul erfolgt mittels Frequenz. Die Signalstärke ist dabei proportional zur Lichtintensität.

Zu beachten: Der OE Pin ist werksseitig mittels R8 / 0 Ω Widerstand auf GND gebrückt, diesbezüglich vor Verwendung des OE Pins den Widerstand entfernen bzw. durch einen Wiederstand mit min. 4,7KΩ ersetzen.

The Color Sensor Module supports power supply between 2.7V to 5V. Therefore the Color Sensor Module works perfect in combination with typical MCU’s such as

  • ESP8266
  • ESP32
  • ESP8285
  • Arduino
  • Raspberry Pi
  • STM
  • and much more

 

The TCS3200 Color Sensor Module is based on a light sensing diode array TCS230 from Taos. The TCS230 has an 8 x 8 array of photodiodes with color filters

  • 16 Red
  • 16 Blue
  • 16 Green
  • 16 Clear

 

A light to frequency converter generates a 50% duty cycle square wave on the output pin. Frequency is directly proportional to light intensity. Output scaling 100%, 20% and 2% allows for wide dynamic range of intensities.

 

The color selects (S2, S3), frequency scale (S0, S1) and output are TTL logic level and can be connected directly to the micro controller. Basic readings are easy using the Arduino “pulsein” command. Take a reading for each color. The reading with narrowest pulse width or highest frequency is the major color. Using advanced ratio analysis almost any color could be recognized.

NOTE: The OE pin (Output Enable ) is grounded through R8 (0ohm), making the module enabled by default. Do not connect the OE to the micro controller, unless R8 is removed or changed to 4.7K or greater.

digital Light Sensor Module Features:

  • Voltage Range: 2.7-5 V
  • Supply Current: 30mA @ 5V
  • Input: TTL Logic Levels
  • Sensor Bandwidth: ~ 400 – 950nm
  • Output: TTL Level Square Wave (50% Duty Cycle)
  • ~2Hz max Dark/24KHz Max,

 

 

Zusätzliche Informationen

Das könnte dir auch gefallen …

Anmelden