ESPDUINO-32 ESP32 Wemos D1 UNO D1 WROOM32 USB CH340 Entwicklerplatine 32Mb/4MB Development Board

ESPDUINO-32 WROOM32 CH340 Arduino Development Board USB 2.0 Type B © androegg

ESPDUINO-32 WROOM32 CH340 Arduino Development Board USB-Micro © androegg

ESPDUINO-32 WROOM32 CH340 Arduino Development Board © androegg

Das ESPDUINO-32 Board basiert auf dem ESP32 WROOM 32 Modul von Espressif und ist wie folgt verfügbar

• USB 2.0 Type B
• USB Micro

Anschluß

Das ESPDUINO-32 Entwicklerboard vereint die typische Arduino Bauform mit dem ESP32.
Der ESP32 WROOM32 basiert auf der Xtensa Dual Core 32bit MCU in Kombination mit einem 4MB SPI Flash Speicher.

ESPDUINO ESP32 WROOM32 Entwicklerboard

Im Vergleich zu typischen ESP32 Entwicklerboards verfügt das ESPDUINO-32 Entwicklerboard neben einer USB Buchse zusätzlich über einen 5,5×2,1mm Hohlsteckeranschluss. Über den Hohlstecker anschluss kann das ESPDUINO-32 mit Eingangsspanungen von 5-12V versorgt werden.

Des Weiteren verfügt das ESPDUINOEntwickler Board über einen CH340 USB TTL Konverter, sodass eine direkte, serielle Kommunikation über die USB Schnittstelle erfolgen kann.

Der ESP32 WROOM32 unterstützt

• 802.11 b/g/n Standard
• HT40 WLan Transceiver
• Bluetooth bis 4.2
• Takfrequenz 160MHz
• SRAM 512kBytes
• 4MB 32Mbit SPI Flash
• unterstützte Schnittstellen
  SPI SD Karte,
  UART,
  SPI,
  SDIO,
  I2C,
  LED PWM,
  Motor PWM,
  I2S,
  IR,
  pulse counter,
  GPIO, capacitive touch sensor,
  ADC 12-bit,
  DAC,
  Two-Wire Automotive Interface (TWAI®), compatible with ISO11898-1 (CAN Specification 2.0)

• USB 2.0 Type B
• USB-Micro

connector

The ESPDUINO-32 developer board combines the typical Arduino design with the ESP32 features. The ESP32 WROOM32 is based on the Xtensa Dual Core 32bit MCU in combination with a 4MB SPI Flash memory.

ESPDUINO ESP32 WROOM32 Development Board

Compared to typical ESP32 development boards, the ESPDUINO-32 development board has besides a USB socket also a 5.5×2.1mm barrel connector. The ESPDUINO-32 can be supplied with input voltages of 5-12V via the barrel connector. Furthermore, the ESPDUINO developer board has a CH340 USB TTL converter on board and support a direct, serial communication thru USB interface.

The ESP32 WROOM32 supports

• 802.11 b/g/n Standard
• HT40 WLan Transceiver
• Bluetooth up to 4.2
• Frequency 160MHz
• SRAM 512kBytes
• 4MB 32Mbit SPI Flash
• supported Interfaces
  SPI SD Karte,
  UART,
  SPI,
  SDIO,
  I2C,
  LED PWM,
  Motor PWM,
  I2S,
  IR,
  pulse counter,
  GPIO, capacitive touch sensor,
  ADC 12-bit,
  DAC,
  Two-Wire Automotive Interface (TWAI®), compatible with ISO11898-1 (CAN Specification 2.0)

ESPDUINO-32 WROOM32 Development Board Features:

• 5-12V Power Supply thru Barrel Jack Connector
• CH340 USB TTL Converter on board
• CPU / MPU:
  Frequency: up to 240 MHz. based on Tensilica LX6 microcontroller with 600 DMIPS
  up to 600 DMIPS448 KByte ROM size
  520 KByte SRAM size
• SPI Flash:
  Flash memory: 32Mbit
  clock frequency: 75 MHz.
  Page program: up to 256 bytes in 0.64ms (TYP) Sector erase: 512Kb in 0.6s
  Bulk erase: 17 – 23 s
  Hardware write protection: protected area size defined by nonvolatile bits BP0, BP1, BP2
  Deep power-down: 1μA (TYP)
  Write Cycles: > 100,000 write cycles per sector Data retention: > 20 Years
• 802.11 b/g/n/e/i protocol
• supports Wi-Fi Direct (P2P)
• soft-AP Integrated TCP/IP protocol stack
• 802.11 n (2.4 GHz), up to 150 Mbps
• 802.11 e: QoS for wireless multimedia technology
• Block ACK
• Fragmentation and defragmentation
• Automatic Beacon monitoring/scanning
• 802.11 i security features: pre-authentication and TSN
• Wi-Fi Protected Access (WPA)/WPA2/WPA2-Enterprise/Wi-Fi Protected Setup (WPS)
• Infrastructure BSS Station mode/SoftAP mode Wi-Fi Direct (P2P), P2P Discovery, P2P Group Owner mode and P2P Power Management
• UMA compliant and certified
• Antenna diversity and selection
• Compliant with Bluetooth v4.2 BR/EDR and BLE specification
• deep sleep current of < 2.5uA
• Class-1, class-2 and class-3 transmitter without external power amplifier
• Enhanced power control
• +10 dBm transmitting power
• NZIF receiver with -98 dBm sensitivity
• Adaptive Frequency Hopping (AFH)
• Standard HCI based on SDIO/SPI/UART
• High speed UART HCI, up to 4 Mbps
• BT 4.2 controller and host stack
• Service Discover Protocol (SDP)
• General Access Profile (GAP)
• Security Manage Protocol (SMP)
• Bluetooth Low Energy (BLE)
• ATT/GATT
• HID
• All GATT-based profile supported
• SPP-Like GATT-based profile
• BLE Beacon
• A2DP/AVRCP/SPP, HSP/HFP, RFCOMM
• CVSD and SBC for audio codec
• Bluetooth Piconet and Scatternet