BME280 3,3V Temperatur Luftdruck Luftfeuchtigkeit Barometer Modul

5,98 

BME280 3,3V Temperatur Luftdruck Luftfeuchtigkeit Barometer Modul

Lieferzeit: sofort

28 vorrätig

Beschreibung

BME280 3,3V Temperatur Luftdruck Luftfeuchtigkeit Barometer Humidity I2C Sensor ESP8266

BME280 Temperature Barometric Humdity Sensor Module © androegg

BME280 3.3V Temperature Barometric Humdity Sensor Module © androegg

BME280 I2C (SPI optional) Sensor Module © androegg

 

Das BME280 Modul basiert auf dem Bosch Sensortec ME280.

Das BME280 Sensor Modul erlaubt die Erfassung von

  • Temperaturen von -40°C bis +85°C
  • Luftfeuchtigkeit von 0% bis 100%
  • Luftdruck von 300 bis 1100 hPa
  • Höhe 0 bis 9000 Meter

 

Standardmässig ist bei dem BME280 3,3V über eine I2C Schnittstelle aktiv (CSB verfügt über einen 10K PullUp), zur Nutzung der SPI Schnittstelle muss dieser auf LOW / GND gesetzt werden.

Das BME280 3,3V Modul unterstützt dabei 2 I2C Adressen, selektierbar über den SDO PIN

  • 0x76 / SDO PullDown
  • 0x77 / SDO PullUp

 

 

Das BME280 Modul verfügt über eine geringe Messabweichung

  • ± 1°C im Messbereich von 0°C bis 60°C
  • ±1,5°C im Messbereich von -40°C bis 0°C und im Messbereich von über +60°C
  • ±3% im Bereich von 0% bis 100% Luftfeuchtigkeit
  • ±1,0 hPa im Messbereich von 300 – 1100 hPa
  • im Bezug der Höhenmessung liefert der BME280 im Bereich von 0-60°C eine max. ABweichung von ±1 Meter, bzw. 1,7 Meter ausserhalb des vorgenannten Temperaturbereichs

The BME Sensor Module is based on Bosch Sensortec ME280.

The BME280 Sensor Module enables

  • Temperature: -40 to 85°C
  • Humidity: 0 to 100%
  • Pressure: 300 to 1100 hPa
  • Altitude: 0 to 30,000 ft

measurements

The BME280 3.3V I2C Bus is activated thru CSB (Chip Select Bus) pin determines which bus to use. A logic HIGH selects the I2C bus. A 10K pull-up resistor on the module pulls this pin HIGH and so the I2C bus is selected by default unless this pin is grounded for active SPI interface.

The I2C Interface of the BME280 supports to addresse thru SDO Pin

  • 0x76 / SDO PullDown
  • 0x77 / SDO PullUp

 

BME280 Module Accuracy

  • ±1°C is obtained over the range of 0 to 65°C. Outside that range, the accuracy can decrease to ±1.5°C
  • humidity over the range of 0 to 100% with an accuracy of ±3%
  • pressure over the range of 300 to 1100 hPa with excellent accuracy of ±1.0 hPa
  • elevation measurement in temperature range of 0 to 65°C with an accuracy of approximately ±1 meter. Outside that range the accuracy can decrease to ±1.7 hPa

BME280 Module Features:

  • 1.7V to 3.6V Input Voltage
  • I2C Interface up to 3.4MHz. (standard), SPI (optional) up to 10 MHz.
  • Measurement
    • Temperature: -40 to 85°C
    • Humidity: 0 to 100%
    • Pressure: 300 to 1100 hPa
    • Altitude: 0 to 30,000 ft
  • Current
    • 1,8 uA @ 1 Hz Humidity and Temperature
    • 2,8 uA @ 1 Hz pressure and Temperature
    • 3,6 uA @ 1 Hz Humidity, Pressure and Temperature
    • 0,1 uA Standby

Zusätzliche Informationen

Das könnte dir auch gefallen …

Anmelden