ESP8266 IoT Relais Board 7-30V

6,79 

Das ESP8266 Relais Board basiert auf dem ESP-12F

Lieferzeit: sofort

28 vorrätig

Beschreibung

ESP8266 IoT Relais Board ESP12-F 32Mbit Flash +25dBm WLan Wifi Modul Arduino

ESP8266 ESP-12F Relay Module © androegg

7 – 30 Volt Relay Module ESP-12F © androegg

7 – 30 Volt Relay Pinout  © androegg

7 – 30 Volt Relay Schematic  © androegg

Das ESP8266 Relais Board basiert auf dem ESP-12F und unterstützt somit zahlreiche SDK’s wie beispielsweise:

  •  Espressif
  • Arduino
  • Nodemcu
  • Microphyton
  • ESPEasy
  • PlatformIO
  • usw.

 

Das Relais wird mittels HIGH/LOW Level des GPIO 4 über einen 2N3904 Transistor gesteuert.

Zusätzlich erlaubt das ESP8266 Relais Board die Benutzereingabe über einen PC817 Optokoppler. Die Benutzereingabe wird seitens des ESP-12F über den GPIO 5 (HIGH/LOW Level) erfasst.

Das ESP8266 Relais erlaubt Eingangsspannungen von 7-30V und eignet sich daher für eine Vielzahl von Anwendungen.

 

Das ESP8266 Relais Modul verfügt über folgende Anschlüsse:

  • P2 Schraubklemme 2-polig
    VCC 7-30V
    GND
  • P6 Pinleiste 3-polig
    TX Data
    RX Data
    GND
  • P5 Pinleiste 2-polig
    Jumper für Flash Modus (brückt GPIO 0 und GND übere einen 10kΩ Widerstand)
  • P3 Schraubklemme 3-polig
    OUT NC
    OUT COMOUT NO
  • P4 Schraubklemme 3-polig
    +5V
    Input 1
    GND

The ESP8266 Relais Board is based on ESP-12F and supports a wide range of ESP8266 SDK’s such as:

  •  Espressif
  • Arduino
  • Nodemcu
  • Microphyton
  • ESPEasy
  • PlatformIO
  • etc.

 

The Relais its controlled thru HIGH/LOW Level over GPIO 4 (switching a 2N3904 Transistor).

The ESP8266 supports also an User Input thru an PC817 Optocoupler connected to GPIO 5 (HIGH / LOW Level).

The ESP8266 Relais supports power supply from 7 -30V DC.

ESP8266 Relais Connections:

  • P2 2-pole Screw Connector
    VCC 7-30V
    GND
  • P6 3-pole Pinheader
    TX Data
    RX Data
    GND
  • P5 2-pole Pinheader
    Jumper for flash mode (connects GPIO 0 and GND over 10 KΩ resistor)
  • P3 3-pole Screw Connector
    OUT NC
    OUT COM
    OUT NO
  • P4 3-pole Screw Connector
    +5V
    Input 1
    GND

ESP8266 Relais Board Features:

  • supports 7-30 Vcc (MP2303 Voltage Regulator)
  • relais function over GPIO
  • integrated ESP8266 ESP-12F Module
  • Jumper for flash mode
  • UART Pinheader
  • VCC power connector
  • PC817 Optokoppler for user input
  • LM1117 3.3V Voltage Converter

ESP-12F Features:

  • CPU / MPU:
    • Frequency: 80 / 160 MHz.
    • Risk: 32-bit
    • Instruction Ram: 64 Kb
    • Data Ram: 96 Kb
  • SPI Flash:
    • Flash memory: 32Mb
    • clock frequency: 75 MHz.
    • Page program: up to 256 bytes in 0.64ms (TYP)
      Sector erase: 512Kb in 0.6s
    • Bulk erase: 17 – 23 s
    • Hardware write protection: protected area size defined by nonvolatile bits BP0, BP1, BP2
    • Deep power-down: 1μA (TYP)
    • Write Cycles: > 100,000 write cycles per sector
      Data retention: > 20 Years
  • 802.11 b/g/n protocol
  • supports Wi-Fi Direct (P2P)
  • soft-AP Integrated TCP/IP protocol stack
  • integrated PCB Antenna
  • +25 dBm output power in 802.11b mode
  • Power down leakage current of < 10uA
  • Integrated low power 32-bit MCU
  • supported Interface
    • SDIO 2.0
    • SPI
    • UART
    • STBC
    • MIMO
  • A-MPDU & A-MSDU aggregation & 0.4μs guard interval
  • Wake up and transmit packets in < 2ms
  • Standby power consumption of < 1.0mW (DTIM3)

Zusätzliche Informationen

Das könnte dir auch gefallen …

Anmelden